Cleaning your QEnergySpa ORB

 

 

Maintain Your QEnergySpa with Proper Cleaning

Cleaning the Q Energy Spa

 

To maintain your system in optimum condition, it is important to clean it.

It is best to clean after every use, especially between different people.

If only you, perhaps every 3-4 uses.

 

 

Cleaning the Q Energy Spa Orb
Outlined below are the factors that need to be considered when cleaning the Orb. Both in the clinic and in your home.

We also recommend some ‘tried and tested’ cleaning solutions that are currently available on the market.



Maintaining your Orb

orb-blue clear-orb
 When cleaning your Orb, four (4) factors need to be considered:

  • Hygiene – Avoid cross contamination from one person to the next.
  • Presentation – A dirty Orb is not a good look in professional practice or clinic.
  • Energy Transfer – Remove all energetic properties of the previous person in session, before embarking on a new session with a different individual.
  • Life of Orb – The longer you soak your Orb in any solution, the shorter the life of the components of the Orb. So soak at a minimum.


To keep your QEnergySpa Orb clean, there are a few different methods that may be employed depending on your situation.

In the Clinic

    Following a session in a clinic or practice setting, it is recommended that you follow these cleaning instructions.                            Following the guidelines below will allow you to get the longest life from your orb, rings, tracks and cable.

  • Rinse your Orb in clean warm water.
  • Place your Orb in a cleaning solution for a few seconds (this will ensure removal of any deposit of sediment or mineral and energetic properties). It is strongly advised that you wear protective gloves when cleaning the Orb using the recommended cleaning solutions.
  • Rinse Orb vigorously in a container of warm water, to wash off the residual cleaning solution and place under fresh running warm water for 30 seconds (your Orb is ready for the next session).
  • At the end of the day, you may like to completely disassemble the Orb and leave it in solution 5 – 15 minutes. This is a good time to inspect all the components and replace the Rings and Tracks if needed. If the Orb shell and Center Module are still dirty after the 15 minutes of soaking in solution; these parts can be soaked for longer.

Note: The field created during session slowly alters the components. Over time the plastic becomes increasingly more brittle. Pulling the Orb apart regularly, ensures that the components don’t adhere, making it difficult to pull apart.

 

Cleaning Solution: CLR
CLR (most supermarkets) This solution should be mixed 1:1; one part (CLR) to one part water. clr This mixture can be stored in a re-sealable container and used many times before needing to be replaced. The solution when first mixed can be relatively aggressive and it is advised that you do not leave your Orb in this solution for longer than the recommended time period (15-30 minutes) as it may degrade Orb components prematurely. Once the solution has been used a few times, this aggressive nature diminishes.
WARNING: Be aware that all of the above mentioned cleaning solutions may damage cupboard, stainless steel, floor and bench top surfaces, in their undiluted and diluted states. Hence, it is always a good idea to clean up spills as soon as they occur. We accept no liability for any damage or injury that may occur by the use of these solvents.

 

A Natural Cleaning Solution

lemon-juicer

  • Rinse your Orb in clean warm water.
  • Prepare your DeScale Magic natural cleaning solution
  • Place your Orb in cleaning solution for 5 minutes between sessions (this will ensure removal of any deposit of sediment or mineral and energetic properties).
  • Rinse Orb vigorously in a container of warm water, to wash off the residual cleaning solution and place under fresh running warm water for 30 seconds (your Orb is ready for the next session).

     Order DeScale Magic

At the end of the day, you may like to pull the Orb apart and leave it in solution 10 – 15 minutes. This is a good time to inspect all the components and replace the Rings & Tracks if needed. If the Orb shell and Center Module are still dirty after the 15 minutes of soaking in solution; these parts can be soaked for longer.

In your home
For home users, the cleaning of the ORB may be carried out as described above. However, to lengthen the life of the ORB components, it is advisable to clean your Orb at a minimum, e.g. every time you replace your positive rings and track set. This will ensure that you do not get an excessive build up of mineral and other deposits that may interfere with the proper function of your QEnergySpa.

 

If however, more than one person is using the Orb, it is recommended that a solution is used between the different users to ensure that no energetic component from the previous person interferes with the session of the next person.

 

 Maintenance

Plate and Track sets replacement.
Water conditions play a large role in the erosion of the positive plates and track. For this reason it is very difficult to put a time frame on when to replace. The easiest way to determine when to change the positive plates and track is to take a close inspection.

Place your finger on the positive plates and track, if it bends, replace it as the metal has deteriorated.

 

When replacing plates or taking the ORB apart please read the manual carefully & check the ORB quick reference guide.

 

PLEASE NOTE:
platechange
When reassembling the Array (pictured) or the Orb, always ensure the top positive ring is sitting on and touching the Positive track . The cable connector hood is fitted flush with the orb.

 

Please take care of the QEnergySpa. Whenever the need arises to ship the system either use the original Styrofoam box inside another bag or box. Sharp objects including other cardboard boxes can easily damage the Styrofoam box. Q The Experience is not responsible of any damage that occurs through owner negligence.

 

Protect the front of the Energy Spa from knocks and scratches. The Attenuator switch on the model 2100, 3024, 3100 and 2500 is prone to damage from strong impacts. Place bubble wrap or foam over the switch whilst in the carry bag.