ORB Assembly Guide

 

 

  This diagram shows all the parts of the Orb and the corresponding number of each part. To avoid any misunderstanding,

please refer to these names and numbers when discussing the Orb assembly with your consultant.

Orb Components:

  1. Bottom Orb Shell (Base)

  2. Bottom Button (Bottom Ring Assembly)

  3. Positive Ring (Sharp Edge facing UP)

  4. Positive Track

  5. Center Module (Copper & two Rings)

  6. Positive Ring (Sharp Edge facing DOWN)

  7. Top Button (Top Ring Assembly)

  8. Top Orb Shell

  9. Cable Connector (Mohawk)

  10. Locking clip

 

Orb II Assembly Exploded

Each step is noted here. Please see below for a step-by-step larger view.

Step 1a.  Begin with the Bottom Shell (Orb Base)

Step 1a Orb Assembly

 

Step 1b. Insert the first Ring with Brass Post.

 

Step 1b Orb Assembly

 

Begin the Assembly by taking

the Bottom Orb Shell (#1).

 

 

Take note of the brass

 

post recess as shown here.

 

 

 

 

 

 

 

 

 

 

Press the Bottom Button (#2) into the

Bottom Orb Shell with the Brass Post

pointing down to fit into the recess.

 

 

 

 

 

Step 2.  Inserting the 2nd Ring.

 

Step 2 Orb Assembly

 

Step 3. Inserting the Positive Track

 

Step 3 Orb Assembly

 

Step 4.  Inserting the Center Module.

 

Step 4 Orb Assembly

 

 

Place one Positive Ring (#3) into the Orb Shell.

For optimal performance please ensure that the

less-rounded edge of the Positive Ring face up.

 

 

 

 

 

 

 

Place the Positive Track (#4)

into the Orb Shell, resting on (A)

the Positive Ring and (B) the

indent on the Orb Shell.

 

 

 

 

 

 

 

 

Fit the Center Module (#5) into the Orb Shell between

the Positive Track arms as shown, (B) ensuring that

the Negative Track (A) is directly opposite the Positive

Track.
The Center Module (#5) should rest on the Bottom

Button (#2) and be level within the Orb Shell.

 

 

 

 

 

Step 5.  Inserting the 2nd Positive Ring.

Step 5 Orb Assembly

 

 

Place the remaining Positive Ring (#6) into the Orb

resting on top of the Positive Track (#4) as shown (A).

For optimal performance please ensure that the

less-rounded edge of the Positive Ring faces down.

 

 

 

Step 6a. Orb Shell Top

Step 6 Orb Assembly

 

 

 

Take the Top Orb Shell (#8)

and locate the hole in the top.

 

 

 

 

 

Step 6b.  Inserting the Top Button.

Step 6b Orb Assembly

 

 

Insert the Top Button (#7) into the

Top Orb Shell so that the Brass Post

protrudes through the hole.

 

Gently rotate it so that it goes in smoothly.

It should hold in firmly.

 

 

 

Step 7a.  Fitting the Top Orb Shell.

Step 7a Orb Assembly

 

 

Align the arrows (A) on the rear of the Orb Shell.

When placed correctly, the Tab on the rear of the

Bottom Orb Shell (B) will match up with the Hole (B)

on the rear of the Top Orb Shell.

 

 

 

 

Step 7b.  Closing the Top Orb Shell.

Step 7b Orb Assembly

 

 

Close the Top and Bottom Orb shells

as if hinged at the back.

 

The small indent in the Top Shell (C)

will align with the Positive Track Eyelet (#4).

 

 

 

 

Step 8a.  Locate Guide Slots.

Step 8a Orb Assembly

 

 

 

Locate the Guide Slots and

the Top Slot in the Orb.

 

 

 

 

 

Step 8b.  Fitting the Cable Connector.

Step 8b Orb Assembly

 

 

Slide the tip of the Cable Connector (#9)

into the Top Slot of the Orb.

 

Align the Guide Pins with the Guide Slots

in the Orb and push the Cable Connector

firmly against the Orb.

 

 

 

Step 9.  Locking the Cable Connector in place.

Step 9 Orb Assembly

 

Ensure that there is no gap between the Orb

and the Cable Connector.

 

Whilst holding the Cable Connector firmly

against the Orb, slide the Locking Clip (#10)

upward fastening the Cable Connector to the Orb.

 

 

 

 

Step 10. Locking the Cable Connector in place.

Step 10 Orb Assembly

 

 

Ensure the Locking Clip clicks

over the top of the Locking

Pins on the Cable Connector.

 

 

 

 

 

 

Your Orb is now complete.

Step 11 Orb Assembly

 

 

Your Orb is now complete!

 

 

You are ready to begin a

QEnergySpa session.

 

 

Remember to never use force, and if in doubt, please call me.

Call Debbie Allen at 303-782-4841